[Scilab-users] GUI Builder 4.0.1 for Scilab 6.0

[Tan Chin Luh]

Hi,

The issue was caused by the changes in code generation for a better 
visualization during the GUI start up. If you notice carefully, your 
Simulation_v1.1.sce will be shown up with all components ready while 
Simulation_v2.6.sce will show the figure first, and the components would 
be loaded one by one.

I had overlooked the reloading the generated GUI file in new format. 
Fixed in ver 4.1.

Currently GUI generated in Scilab 6 is not backward compatible yet, I 
will find some time to update the version 3 for Scilab 5.5.2.

Thanks.

Regards,
Tan Chin Luh

On 4/5/2017 6:32 PM, Frieder Nikolaisen wrote:
>
> Dear Antoine,
>
> yes. I stick to Scilab 5.5. I will copy this message to the report.
>
> Cheers
>
> Frieder
>
> Am 2017-05-04 11:55, schrieb amonmayr at laas.fr:
>
>> Dear Frieder,
>>
>> In Scilab 6.0 a breaking change was introduced: adding an empty 
>> matrix to a constant now gives an empty matrix, not a constant.
>> This causes a lot of issues with existing codes that relied on the 
>> old behaviour.
>> Apparently, this is the case for GUI Builder that was not properly 
>> refactored for Scilab 6.0.
>> I think you should report this to the maintainer of the module.
>>
>> Hope it helps,
>>
>> Antoine
>>
>>
>> Le 04/05/2017 à 09:13, Frieder Nikolaisen a écrit :
>>>
>>> Dear Community,
>>>
>>> I am using the GUI Builder again (last time Oktobre 2016), now with 
>>> Scilab 6.0.0.
>>>
>>> I started to Design the interface, generated the GUI. Had the GUI 
>>> run and wanted to reload it. But:
>>>
>>>
>>> --> guibuilder
>>> operation -: Warning adding a matrix with the empty matrix will give 
>>> an empty matrix result.
>>> operation +: Warning adding a matrix with the empty matrix will give 
>>> an empty matrix result.
>>> at line    60 of function guigetfile
>>> at line     4 of function openfile
>>> at line     9 of function open_existing_gui
>>>
>>> ':': Wrong type for argument 1: Real scalar expected.
>>>
>>> And with the old version I am used to (but its still desigend with 
>>> Scilab 6):
>>>
>>> START GUI Builder 3.0 for Scilab 5.5
>>>     Load macros
>>>     Load help
>>>     Type "guibuilder" to start the GUI
>>>
>>>
>>> -->guibuilder
>>>   !--error 21
>>> ungültiger Index.
>>> at line       8 of function openfile called by :
>>> at line       9 of function open_existing_gui called by :
>>> = gcbo; end;gcbo = 
>>> getcallbackobject(118);open_existing_gui(handles);if 
>>> exists("%oldgcbo") then gcbo = %oldgcbo; else clear gcbo; end
>>> while executing a callback
>>>
>>> The file is attached.
>>>
>>> Scilab 5.5 and 6 open the programm with save and run. But not with 
>>> the Builder.
>>>
>>> *Whats wrong?*
>>>
>>> Best regards
>>>
>>> Frieder
>>>
>>>
>>>
>>> _______________________________________________
>>> users mailing list
>>> users at lists.scilab.org
>>> http://lists.scilab.org/mailman/listinfo/users
>>
>> -- 
>> +++++++++++++++++++++++++++++++++++++++++++++++++++++++
>>
>>   Antoine Monmayrant LAAS - CNRS
>>   7 avenue du Colonel Roche
>>   BP 54200
>>   31031 TOULOUSE Cedex 4
>>   FRANCE
>>
>>   Tel:+33 5 61 33 64 59
>>   
>>   email :antoine.monmayrant at laas.fr
>>   permanent email :antoine.monmayrant at polytechnique.org
>>
>> +++++++++++++++++++++++++++++++++++++++++++++++++++++++
>>
>
>
> _______________________________________________
> users mailing list
> users at lists.scilab.org
> http://lists.scilab.org/mailman/listinfo/users


-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://lists.scilab.org/pipermail/users/attachments/20170505/82d634b4/attachment.htm>